Meridian SEED EXPRESS 240 RT Скачать руководство пользователя страница 49

Страница: 49 / 96

3. The chain must always be kept snug but not

too tight. To check the tightness of the chain:

a. On the slack side of the chain, between

the drive sprocket and rotating sprocket,

push the chain inward.

b. Now pull the chain outward.

c. The distance the chain travels, side-to-

side,shouldbebetween1/8”inchand

1/4”.

d. If the travel exceeds this amount,

tighten the chain using the adjustment

mechanism.

4. Remove any dirt or debris on the chain. Dirt

buildup on the roller chain and sprockets will

have an abrasive effect when suspended in

lubrication and can cause premature wear.

5. Check for signs of wear on the inner surfaces

of the roller chain and teeth of the sprockets.

Inspectthechainforflexibility,makingcertain

that each and every link joint is free to pivot.

7. The roller chain will stretch and elongate

over the life of the tender. A chain should be

replacedifanyorallofthepitches(distance

fromonepintotheadjoiningpin)exceed

41/64”.

8. Check the entire chain for any signs of fatigue

such as cracks, loose pins, or loose bushings.

Also check for corrosion or pitted surfaces.

Replace any damaged chain.

9. Check the sprockets for signs of wear, such

as cracks, thinning of the teeth, hook-shaped

teeth, or wear patterns on the sides of the

teeth. Also check for corrosion or pitted

surfaces. Replace any damaged sprockets.

10.7 TRAILER BREAK-AWAY SYSTEM

10.7.1 Testing the Battery

1. Disconnect the trailer plug from the tow

vehicle; otherwise, you are testing the tow

vehicle’s battery.

2. Press the green TEST button on the control

box located inside the frame of the trailer. The

green indicator light should illuminate if the

battery is fully charged. If the yellow or red

indicator lights illuminate, the unit’s battery

should be charged before towing the trailer.

IMPORTANT

Ifthebatteryisweakordead(redindicator,even

aftercharging),asindicatedbytheindicatorlight,

the battery must be replaced.

3. Plug the trailer into the tow vehicle. The

yellow“Charging”lightshouldbeON.

4. Test the system by pulling the pin out of the

break-away switch. The battery will activate

thebrakes.(

Note

: Do not use this kit as a

parkingbrake).Thebatteryshouldbecharged

and tested prior to each trailer outing.

Содержание SEED EXPRESS 240 RT

































































































Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды

Meridian SEED EXPRESS 240 RT, Руководство оператора

Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды