Meridian SEED EXPRESS 240 RT Скачать руководство пользователя страница 27

Страница: 27 / 96

5.3 CONTROL SYSTEM FUNCTIONS

The MEGA REMOTE system is a state-of-the-art

microprocessorbasedRadioFrequency(RF)

control system. It provides the operator the ability

to operate the seed tender from the control panel

or from the handheld wireless remote control.

5.3.1 Control Functions

The controls on this panel are intended to be used

only as a backup resource. All of the functions

of the seed tender can more easily be controlled

using the handheld wireless remote control.

On/Off Key Switch (1)

This key switch controls the power to the electrical

system. Turn the key clockwise to turn the

electrical system ON. The key must be in the ON

position for the engine to start or the handheld

wireless remote control to function. Turn the

key counterclockwise to turn OFF the electrical

system.

Starting the Engine (2)

Press and hold this button until the engine starts.

Also set the choke lever on the engine when

starting the engine. Turn the key counterclockwise

to turn OFF the engine.

Conveyor ON and OFF (3)

This toggle switch starts and stops the conveyor

belt. Press the toggle switch UP to start the

conveyor. Press the toggle switch DOWN to stop

the conveyor.

Conveyor Swing Left and Swing Right (4)

This toggle switch positions the conveyor to the

right or left. Press the toggle switch to the LEFT to

position the conveyor to the left or the passenger’s

side of the tow vehicle. Press the toggle switch to

the RIGHT to position the conveyor to the right or

the driver’s side of the tow vehicle.

Conveyor Lift and Lower (5)

This toggle switch raises and lowers the conveyor.

Press the toggle switch UP to raise the conveyor.

Press the toggle switch DOWN to lower the

conveyor.

Slide Gate 1 (6)

This toggle switch opens and closes the slide gate

at the bottom of compartment 1. Press the toggle

switch UP to open the slide gate, and press the

toggle switch DOWN to close the slide gate. The

openingcanbevariedtoprovidethedesiredflow

rate of seed onto the conveyor belt.

Slide Gate 2 (7)

This toggle switch opens and closes the slide gate

at the bottom of compartment 2. Press the toggle

switch UP to open the slide gate, and press the

toggle switch DOWN to close the slide gate. The

openingcanbevariedtoprovidethedesiredflow

rate of seed onto the conveyor belt.

Содержание SEED EXPRESS 240 RT

































































































Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды

Meridian SEED EXPRESS 240 RT, Руководство оператора

Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды