Meridian SEED EXPRESS 240 RT Скачать руководство пользователя страница 46

Страница: 46 / 96

10.5 BELT DELIVERY TUBE
10.5.1 Unplugging

IMPORTANT

Do not operate the conveyor when it is plugged

with excess seed or is hindered from moving by

a foreign object. Continued operation can cause

damage to the conveyor or result in a broken

conveyor belt.

If the conveyor becomes plugged, follow this

procedure:

1. Position the conveyor with easy access to

both ends.

2. Stop the engine and remove the ignition key.

Place a lock-out tag on the control box to

prevent accidental starting of the conveyor.

3. Open the lower access door at the bottom of

the conveyor and remove any excess seed or

obstruction.

4. Close and secure the lower access door.

5. Also check the delivery hood for blockage and

remove any obstructions.

6. In some extreme case it may be necessary to

remove the galvanized belt guards and/or the

belt itself.

10.5.2 Belt Tension Adjustment

1. Loosen the locknut on each side of the belt

tension mechanism.

2. Tighten the two adjusting bolts equally to

23 ft-lbs. While holding the adjusting bolt in

place, retighten both locking nuts.

3. Start the conveyor and make sure the belt

is tracking in the center of the drive drum. If

the belt is not tracking properly, use the Belt

Tracking Adjustment procedure to correct the

problem.

IMPORTANT

The drive drum at the bottom of the conveyor must

besquare(driveshaftmustbeequaldistancefrom

endofunit)forthebelttotrackproperly.

Содержание SEED EXPRESS 240 RT

































































































Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды

Meridian SEED EXPRESS 240 RT, Руководство оператора

Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды