manualshive.com logo in svg

Mercury Sterndrive QSD 2.0, Руководство пользователя

Поделиться
Скачать
Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 89

Section 5 - Maintenance

90-8M0069751   

eng

  APRIL  2012

Page  81

4. Move the fuel lines so they do not obstruct access to the engine coolant drain plug.

Port side of engine

a -

Throttle cable bracket

b -

14–pin electrical connector

c -

Water–separating fuel filter

d -

Fuel cooler with fuel lines moved to provide access

e -

General location of engine coolant drain plug

f -

Engine control module

5. Remove the engine coolant drain plug and drain the coolant into a suitable container.

NOTE: Allow the engine coolant system to drain completely.
NOTE: Dispose of old coolant properly.

Port side of block with

water–separating fuel

filter removed for access

a -

Engine coolant drain

plug

6. Ensure that the coolant has drained completely.
7. If required, clean the closed cooling system. See your local Mercury Diesel authorized repair facility.
8. Install and tighten the engine coolant drain plug.
9. Reinstall the water–separating fuel filter. Refer to 

Water–Separating Fuel Filter, Replacing.

10. Fill the system with the specified coolant. Refer to 

Filling the Closed Cooling System

.

Filling the Closed Cooling System

1. Remove the pressure cap.

QSD 2.0L (engine cover removed)

a -

Pressure cap

b -

Coolant expansion tank

c -

Coolant fill neck

25571

a

b

c

d

e

f

a

25768

a

b

c

25356

Содержание Sterndrive QSD 2.0




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды