Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 106

Страница: 106 / 131

Section 5 - Maintenance

Page 98

90-8M0069751

eng

APRIL 2012

Tighten the gimbal ring U‑bolt nuts to specification.

a -

Transom assembly

b -

Gimbal ring U‑bolt nuts

Description

lb–in.

lb–ft

Gimbal ring U‑bolt nuts for 3/8 in. U‑bolt

–

Gimbal ring U‑bolt nuts for 7/16 in. U‑bolt

–

Engine Mounts

Loosen the rear engine mount bolts 1 to 1‑1/2 turns. Retorque the rear engine mount bolts.

a -

Rear engine mount

b -

Transom plate mount

c -

Rear engine mount bolt

Description

lb. in.

lb. ft.

Rear engine mounts

Propellers

Alpha Propeller Removal

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the water with a propeller installed.

Before installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the

engine from starting. Place a block of wood between the propeller blade and the anti‑ventilation plate.

1. Place wood block between propeller blade and anti‑ventilation plate to prevent rotation. Straighten bent tabs on tab

washer.

19624

19622

Содержание Sterndrive QSD 2.0




































































































































Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды

Mercury Sterndrive QSD 2.0, Руководство пользователя

Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды