Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 124

Страница: 124 / 131

Section 7 - Troubleshooting

Page 116

90-8M0069751

eng

APRIL 2012

Diagnosing Electronically Controlled Fuel System Problems

A Mercury Diesel authorized repair facility has the proper service tools for diagnosing problems on electronically controlled fuel

systems. The engine control module (ECM) on these engines has the ability to detect problems with the system when they

occur, and store a trouble code in the ECM's memory. This code can then be read later by a service technician using a special

diagnostic tool.

Troubleshooting Charts

Starter Motor Will Not Crank Engine, or Cranks Slow

Possible Cause

Remedy

Battery switch turned off.

Turn switch on.

Remote control not in neutral position.

Position control lever in neutral.

Open circuit breaker or blown fuse.

Check and reset circuit breaker or replace fuse.

Loose or dirty electrical connections or damaged

wiring.

Check all electrical connections and wires (especially battery

cables). Clean and tighten faulty connection.

Bad battery.

Test and replace if bad.

Engine Will Not Start, or Is Hard to Start

Possible Cause

Remedy

Lanyard stop switch activated.

Check lanyard stop switch.

Improper starting procedure.

Read starting procedure.

Empty fuel tank or fuel shut‑off valve closed. Fill tank or open valve.
Throttle not operating properly.

Check the throttle for freedom of movement.

Faulty electrical stop‑circuit.

Have a Mercury Diesel authorized repair facility service the electrical stop

circuit.

Clogged fuel filters.

Replace fuel filters.

Stale or contaminated fuel.

Drain tank. Fill with fresh fuel.

Fuel line or tank vent line kinked or clogged. Replace kinked lines or blow out the lines with compressed air to remove

obstruction.

Air in fuel injection system.

Purge fuel injection system.

Faulty wire connections.

Check wire connections.

Electronic fuel system fault.

Have the electronic fuel system checked by a Mercury Diesel authorized repair

facility.

Engine Runs Rough, Misses, or Backfires

Possible Cause

Remedy

Throttle not operating properly.

Check the throttle for binding or an obstruction.

Idle speed too low.

Have idle speed checked and adjusted by a Mercury Diesel authorized

repair facility.

Clogged fuel or air filters.

Replace fuel or air filters.

Stale or contaminated fuel.

If fuel is contaminated, drain tank. Fill with fresh fuel.

Kinked or clogged fuel line or fuel tank vent line. Replace kinked lines or blow out lines with compressed air to remove

obstruction.

Air in fuel system.

Purge fuel injection system.

Electronic fuel system faulty.

Have electronic system checked by a Mercury Diesel authorized repair

facility.

Содержание Sterndrive QSD 2.0




































































































































Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды

Mercury Sterndrive QSD 2.0, Руководство пользователя

Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды