manualshive.com logo in svg

Mercury Sterndrive QSD 2.0, Руководство пользователя

Поделиться
Скачать
Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 113

Section 5 - Maintenance

90-8M0069751   

eng

  APRIL  2012

Page  105

Description

Nm

lb–in.

lb–ft

Bravo Three front propeller nut

136

–

100

5. Slide the aft thrust hub onto the propeller shaft with the tapered side toward the propeller hub.
6. Align the splines and install the aft propeller.
7. Install the propeller nut and torque.

NOTE: The propeller torque stated is a minimum torque value.

Description

Nm

lb–in.

lb–ft

Bravo Three rear propeller nut

81

–

60

8. Install the propeller shaft anode and screw and torque.

Bravo Three

a -

Rear propeller nut

b -

Rear propeller

c -

Rear propeller thrust hub

d -

Front propeller nut

e -

Front propeller

f -

Front propeller thrust hub

g -

Propeller shaft anode screw

h -

Flat washer

i -

Star washer

j -

Propeller shaft anode

Description

Nm

lb–in.

lb–ft

Propeller shaft anode screw

19

168

–

Drive Belts

QSD 2.0 Drive Belts

All drive belts must be periodically inspected for tension and condition, such as excessive wear, cracks, fraying, or glazed

surfaces.

!

 WARNING

Inspecting the belts with the engine running may cause serious injury or death. Turn off the engine and remove the ignition

key before adjusting tension or inspecting belts.

QSD 2.0L front cover removed

a -

Serpentine belt

b -

Power assisted steering belt

e

f

a

b

c

d

5304

g h

i

j

a

b

25603

Содержание Sterndrive QSD 2.0




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды