manualshive.com logo in svg

Mercury Sterndrive QSD 2.0, Руководство пользователя

Поделиться
Скачать
Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 2

C.2 Owner’s manual

☐

☒

☐

Owner's manual

This declaration of conformity is issued under the sole responsibility of the manufacturer. I declare on behalf of the engine

manufacturer that the engine(s) will meet the exhaust emission requirements of Directive 94/25/EC as amended by Directive

2003/44/EC when installed in a recreational craft, in accordance with the engine manufacturer’s supplied instructions and that

this (these) engine(s) must not be put into service until the recreational craft into which it is (they are) to be installed has been

declared in conformity with the relevant provisions of the above mentioned Directives.

Name / function:

Mark Schwabero, President, Mercury

Marine

Signature and title:

Date and place of issue:

April 20, 2012

Fond du Lac, Wisconsin, USA

Identification Record

Please record the following information:

Engine Model and Horsepower

Engine Serial Number

   

Transom Assembly Serial Number (Sterndrive)

Gear Ratio

Sterndrive Unit Serial Number

   

Transmission Model (Inboard)

Gear Ratio

Transmission Serial Number

   

Propeller Number

Pitch

Diameter

   

Hull Identification Number (HIN)

Purchase Date

   

Boat Manufacturer

Boat Model

Length

   

Exhaust Gas Emissions Certification Number

   

The serial numbers are the manufacturer’s keys to numerous engineering details that apply to your Mercury Diesel power

package. When contacting Mercury Marine about service, 

always specify model and serial numbers.

Descriptions and specifications contained herein were in effect at the time this guide was approved for printing. Mercury

Marine, whose policies are based on continuous improvement, reserves the right to discontinue models at any time or to

change specifications or designs without notice and without incurring obligation.
Mercury Marine, Fond du Lac, Wisconsin, U.S.A. Printed in U.S.A.
Mercury, Mercury Marine, MerCruiser, Mercury MerCruiser, Mercury Racing, Mercury Precision Parts, Mercury Propellers,

Quicksilver, #1 On The Water, Alpha, Bravo, Bravo Two, Bravo Three, MerCathode, RideGuide, SmartCraft, Zero Effort, M with

Waves logo, Mercury with Waves logo, VesselView, and SmartCraft logo are all registered trademarks of Brunswick

Corporation. Mercury Product Protection logo is a registered service mark of Brunswick Corporation.

Welcome

You have selected one of the finest marine power packages available. It incorporates numerous design features to assure

operating ease and durability.
With proper care and maintenance, you will thoroughly enjoy using this product for many boating seasons. To ensure maximum

performance and carefree use, we ask that you thoroughly read this manual.
The Operation, Maintenance and Warranty Manual contains specific instructions for using and maintaining your product. We

suggest that this manual remain with the product for ready reference whenever you are on the water.
Thank you for purchasing one of our Mercury Marine products. We sincerely hope your boating will be pleasant!

Mercury Marine

Содержание Sterndrive QSD 2.0




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды