manualshive.com logo in svg

Mercury Sterndrive QSD 2.0, Руководство пользователя

Поделиться
Скачать
Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 78

Section 5 - Maintenance 

Page  70

90-8M0069751   

eng

  APRIL  2012

1. Move the primer plunger up and down repeatedly.

a -

Fuel priming pump

2. Attempt to start the engine.

Filling (Bleeding)

NOTE: Follow this procedure if the fuel system was run dry or if part of the fuel system was drained for a service function.

1. See 

Water Separating Fuel Filter 

‑ 

Filling

 and fill the fuel filter.

2. Check the filter and drain cap for fuel leaks. Ensure that the bleed screw on the fuel filter bracket is closed.

Fuel Tank Cleaning and Flushing

IMPORTANT: Diesel fuel should not be left in the tank during winter storage, as an accumulation of rust, sludge, and wax

residue will form.
Refer to the boat manufacturer's instructions and clean the fuel tank at specified intervals. Unless specified otherwise, flush and

clean the diesel fuel tank every 1000 hours or five years, whichever occurs first.

Seawater System

Draining the Seawater System

!

 CAUTION

Water can enter the bilge when the drain system is open, damaging the engine or causing the boat to sink. Remove the boat

from the water or close the seacock, disconnect and plug the seawater inlet hose, and ensure the bilge pump is operational

before draining. Do not operate the engine with the drain system open.

IMPORTANT: The engine must be as level as possible to ensure complete draining of the seawater system.
Drain the seawater system before flushing or prior to cold weather (freezing temperature), seasonal storage, or extended

storage.
IMPORTANT: The engine must not be operating during this procedure.

!

 CAUTION

Water can enter the bilge when the drain system is open, damaging the engine or causing the boat to sink. Remove the boat

from the water or close the seacock, disconnect and plug the seawater inlet hose, and ensure the bilge pump is operational

before draining. Do not operate the engine with the drain system open.

1. Remove the boat from the water if possible.

25985

a

Содержание Sterndrive QSD 2.0




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды