Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 20

Страница: 20 / 131

Section 2 - Getting to Know Your Power Package

Page 12

90-8M0069751

eng

APRIL 2012

The following types of gauges may be included with your power package.

26019

Typical gauges

Reference

Gauge

Function

Oil pressure gauge

Indicates engine oil pressure.

Battery meter

Indicates battery voltage.

Coolant temperature gauge

Indicates engine operating temperature.

Fuel gauge

Indicates quantity of fuel in tank.

Power trim gauge

Indicates sterndrive angle (trim up [out] and down [in]).

VesselView (if equipped)

Your power package may be connected to a SmartCraft VesselView display. The interactive VesselView display continuously

reports real‑time information about speed and performance, engine fault codes, fuel status, water temperature and depth, and

other operating data. When VesselView detects a problem with any connected system, it displays an alarm message to the

boat operator.

24797

Typical VesselView display

VesselView may also be connected to other vessel systems such as GPS, generators, and cabin environmental controls. This

vessel integration allows the operator to monitor and control a wide range of vessel systems from a single display.
Refer to your VesselView operations manual for detailed instructions on how to operate this display.

Содержание Sterndrive QSD 2.0




































































































































Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды

Mercury Sterndrive QSD 2.0, Руководство пользователя

Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды