Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 116

Страница: 116 / 131

Section 5 - Maintenance

Page 108

90-8M0069751

eng

APRIL 2012

Battery Switches.

Battery switches should always be positioned so that each engine is operating off of its own battery. Do not

operate engines with switches in the

both

all

position. In an emergency, another engine's battery can be used to start an

engine with a dead battery.

Battery Isolators.

Isolators can be used to charge an auxiliary battery used for powering accessories in the boat. They should

not be used to charge the battery of another engine in the boat unless the type of isolator is specifically designed for this

purpose.

Generators.

The generator's battery should be considered another engine's battery.

Содержание Sterndrive QSD 2.0




































































































































Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды

Mercury Sterndrive QSD 2.0, Руководство пользователя

Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды