Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 107

Страница: 107 / 131

Section 5 - Maintenance

90-8M0069751

eng

APRIL 2012

Page 99

2. Turn propeller shaft nut counterclockwise to remove nut.
3. Slide tab washer, drive sleeve, propeller and thrust hub off propeller shaft.

Alpha Propeller Installation

NOTICE

Operating the engine with a loose propeller can damage the propeller, the drive, or drive components. Always tighten the

propeller nut or nuts to specification and check for tightness periodically and at the required maintenance interval.

IMPORTANT: If reusing tab washer, carefully inspect tabs for cracks or other damage. Replace tab washer if condition is

questionable.

a -

Propeller shaft

b -

Thrust hub

c -

Flo‑Torq II drive hub

d -

Propeller

e -

Drive sleeve

f -

Locking tab washer

g -

Propeller nut

1. Apply a liberal coat of one of the following lubricants to the propeller shaft.

Tube Ref No.

Description

Where Used

Part No.

Special Lubricant 101

Propeller shaft

92-802865Q02

Anti-Corrosion Grease

Propeller shaft

92-802867Q 1

2-4-C Marine Lubricant

with PTFE

Propeller shaft

92-802859A 1

2. Slide thrust hub onto propeller shaft, with stepped side toward propeller hub.
3. Install Flo‑Torq II Drive Hub into propeller.

NOTE: The drive sleeve is tapered and will slide fully into the propeller as the nut is tightened and properly torqued.

4. Align splines and place propeller on propeller shaft.
5. Install drive sleeve and locking tab washer.
6. Install and torque the propeller nut.

Description

lb‑in.

lb‑ft

Propeller nut (minimum)

–

7. Bend three tabs on the tab washer down into the grooves in spline washer. After the first use, bend the three tabs straight

and retorque the propeller nut. Bend tabs back down into spline washer. Check propeller at least after 20 hours of

operation. Do not operate with loose propeller.

Bravo Diesel Sterndrive Propeller Removal

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the water with a propeller installed.

Before installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the

engine from starting. Place a block of wood between the propeller blade and the anti‑ventilation plate.

6215

Содержание Sterndrive QSD 2.0




































































































































Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды

Mercury Sterndrive QSD 2.0, Руководство пользователя

Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды