Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 94

Страница: 94 / 99

•

Ignition system component failure.

Performance Loss

POSSIBLE CAUSES

•

Overheating ‑ Warning horn not working.

•

Low oil pressure. Check oil level.

•

Throttle not opening fully.

•

Damaged propeller or improper propeller size.

•

Incorrect engine timing, adjustment, or setup.

•

Boat overloaded or load improperly distributed.

•

Excessive water in bilge.

•

Boat bottom is dirty or damaged.

Battery Will Not Hold Charge

POSSIBLE CAUSES

•

Battery connections are loose or corroded.

•

Low electrolyte level in battery.

•

Worn out or inefficient battery.

•

Excessive use of electrical accessories.

•

Defective rectifier, alternator, or voltage regulator.

•

Open circuit in the alternator output wire (fused link).

TROUBLESHOOTING

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 94 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: