Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 84

Страница: 84 / 99

Crankcase Oil Pump

802889A1

11591

Aids in the removal of engine oil without

draining the crankcase.

Oil Drain Hose

8M0137866

64627

Aids in the removal of engine oil without

draining the crankcase. Connect to the

crankcase oil pump.

6. Install the crankcase oil pump assembly onto the dipstick tube. Verify the

pump is securely attached to the tube by pulling it up lightly.

a -

Oil drain hose

b -

Lock button

7. Place the drain tube of the crankcase oil pump into an appropriate

container. The container should be large enough to hold more than

9.8 Liter (10 US qt).

8. Extract the engine oil with the pump.
9. Allow the drain tube to completely drain before removing the oil pump

from the dipstick tube.

10. Press on the oil drain hose lock button to release it from the dipstick tube.

63843

MAINTENANCE

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 84 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: