Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 7

Страница: 7 / 99

General Information

Boater's Responsibilities..................................................................................... 1

Before Operating Your Outboard........................................................................ 1

Boat Horsepower Capacity................................................................................. 1

High‑Speed and High‑Performance Boat Operation.......................................... 2

Propeller Selection..............................................................................................2

Outboard Remote Control Models ..................................................................... 4

Lanyard Stop Switch........................................................................................... 5

Protecting People in the Water........................................................................... 7

Passenger Safety Message ‑ Pontoon Boats and Deck Boats...........................8

Wave and Wake Jumping................................................................................... 9

Impact with Underwater Hazards......................................................................10

Exhaust Emissions........................................................................................... 11

Selecting Accessories for Your Outboard......................................................... 13

Safe Boating Recommendations...................................................................... 13

Recording Serial Number................................................................................. 16

Specifications—300R HD................................................................................. 17

Component Identification.................................................................................. 19

Gearcase Identification..................................................................................... 20

Transporting

Trailering Boat/Outboard.................................................................................. 21

Fuel and Oil

Fuel Requirements........................................................................................... 22

Fuel Additives................................................................................................... 23

Low Permeation Fuel Hose Requirement ........................................................ 23

Fuel Demand Valve (FDV) Requirement.......................................................... 23

Engine Oil Recommendations—Race (R) Models............................................24

Checking and Adding Engine Oil...................................................................... 24

Features and Controls

Adaptive Speed Control.................................................................................... 28

Remote Control Features................................................................................. 28

Warning System............................................................................................... 28

Power Trim and Tilt...........................................................................................31

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 7 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: