Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 65

Страница: 65 / 99

3. Battery cable terminals should be clean, tight, and correctly installed.

Positive to positive and negative to negative.

4. Ensure the battery is equipped with a nonconductive shield to prevent

accidental shorting of battery terminals.

Battery Cables and Clean Power Harness

The battery cable connections should be checked often for corrosion or loose

retaining hardware. Maintaining this electrical connection helps ensure the

engine operation and accessories functionality remains trouble‑free. The

engine starting battery cables and the clean power harness wires must be

secured to the engine starting battery with nuts. Wing nuts are not acceptable.

The clean power harness must be secured to one of the battery cables with a

cable tie or other type of secure fastener.

a -

14‑pin data harness

b -

Clean power harness connector at engine

c -

Clean power harness

d -

Battery

e -

Negative engine battery cable

f -

Positive engine battery cable

If the clean power harness fuse is open, try to locate and correct the cause of

the overload. If the cause is not found, the fuse may open again. Remove the

clean power fuse and look at the silver band inside the fuse. If the band is

broken (open), replace the fuse with the same rating (5 amp) and type fuse.

26984

MAINTENANCE

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 65 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: