Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 22

Страница: 22 / 99

STAY CLEAR OF EXHAUST AREAS

41127

Engine exhaust gases contain harmful carbon monoxide. Avoid areas of

concentrated engine exhaust gases. When engines are running, keep

swimmers away from the boat, and do not sit, lie, or stand on swim platforms or

boarding ladders. While underway, do not allow passengers to be positioned

immediately behind the boat (platform dragging, teak/body surfing). This

dangerous practice not only places a person in an area of high engine exhaust

concentration, but also subjects them to the possibility of injury from the boat

propeller.

GOOD VENTILATION

Ventilate the passenger area, open side curtains or forward hatches to remove

fumes.
Example of desired air flow through the boat:

POOR VENTILATION

Under certain running and/or wind conditions, permanently enclosed or canvas

enclosed cabins or cockpits with insufficient ventilation may draw in carbon

monoxide. Install one or more carbon monoxide detectors in your boat.
Although the occurrence is rare, on a very calm day, swimmers and

passengers in an open area of a stationary boat that contains, or is near, a

running engine may be exposed to a hazardous level of carbon monoxide.

GENERAL INFORMATION

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 22 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: