Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 99

Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 66

IMPORTANT: An ATC fuse has the fuse element enclosed or sealed inside the

plastic housing. This type of fuse must be used for marine applications. Marine

applications are exposed to environments that may have the potential to

accumulate explosive vapors. ATO fuses have exposed elements and should

never be used in marine applications.

a -

Nuts

b -

Clean power harness

c -

Cable tie

d -

Good fuse

e -

Open fuse

BATTERY CONNECTIONS

IMPORTANT: The engine electrical system is negative (–) ground.
When connecting the engine battery, hex nuts must be used to secure the

battery leads to the battery posts. Tighten the hex nuts to the specified torque.

Description

Nm

lb‑in.

lb‑ft

Battery hex nuts

13.5

120

–

ORDER OF CONNECTION

Connect the battery cables in the following order:

1. All jumpers between parallel, multiple battery packs
2. From the batteries to the positive (+) engine lead
3. From the batteries to the positive (+) clean power
4. From the batteries to the negative (–) engine lead
5. From the batteries to the negative (–) clean power
6. From the batteries or main ground (–) bus to the negative (–) starboard

helm main power relay

b

a

c

64518

d

e

MAINTENANCE

56

eng

«
...
64
65
66
67
68
...
»

Содержание 300R HD CMS Mechanical




































































































Отзывы:

Нет отзывов