Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 36

Страница: 36 / 99

4. Remove the dipstick and observe the area of the five beads.

a -

Service access door

b -

Oil fill cap

c -

Dipstick

5. The bead or crosshatch which shows oil furthest from the end is the oil

level.

65509

Oil level example

NOTE: New oil (level) may be difficult to identify which is why the crosshatch

between the beads are part of the dipstick assembly. When checking the oil

level, if oil is on any of the five oil range beads or four crosshatch, the oil level

is within the safe operating range. When the oil level is only on the lowest oil

range bead, the operator can add 1.8 Liter (2 US qt) of oil and the level will

remain within the safe operating range. When the oil becomes dark from hours

of product use, it will be easier to identify the oil level on the dipstick.

63305

FUEL AND OIL

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 36 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: