Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 35

Страница: 35 / 99

IMPORTANT: Do not overfill. Tilt the outboard out/up past vertical for

approximately one minute to allow trapped oil to drain back to the oil sump. The

outboard must be in a vertical (not tilted) position when checking the engine oil.

For accurate readings, check the oil only when the engine is cold or after the

engine has not run for at least an hour.

1. Before starting a cold engine, tilt the outboard out/up past vertical to allow

trapped oil to drain back to the oil sump. Allow the outboard to remain

tilted for approximately one minute.

2. Tilt the outboard to a vertical operating position.
3. Push down on the port side of the service access door to unlock and open

the door.

64230

Push here to unlock

NOTE: On the underside of the service access door is a quick reference decal

which lists the type of oil to use on various products.

64634

Quick reference decal

FUEL AND OIL

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 35 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: