Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 62

Страница: 62 / 99

Flushing the Cooling System

Flush the internal water passages of the outboard with fresh water after each

use in salt, polluted, or muddy water. This will help prevent a buildup of

deposits from clogging the internal water passages.

NOTE: The outboard can be tilted or in the vertical operating position during

flushing.

1. With the engine turned off, place the outboard in either the operating

position (vertical) or in a tilted position.

2. Remove the flush connector from the bottom cowl.
3. Remove the cover from the flush connector and thread a water hose into

the flush connector.

64241

4. Turn on the water tap (1/2 maximum) and let the water flush through the

cooling system for about 15 minutes.

5. When flushing is complete, turn off the water and disconnect the water

hose.

6. Install the cover on the flush connector. Place the flush connector back

into the bottom cowl.

Top Cowl Removal and Installation

NOTE: It is recommended to remove and install the cowl while standing inside

the boat.
REMOVAL

1. Tilt the outboard up so the top of the cowl is facing you.

MAINTENANCE

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 62 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: