Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 37

Страница: 37 / 99

IMPORTANT: Repeated removal and insertion of the dipstick will

subsequently deposit oil further up the dipstick tube which potentially may

cause an error reading the oil level.

a -

Safe operating range

b -

General area after an oil change

c -

Add 1.8 Liter (2 US qt) of oil

6. If none of the beads shows the oil level, remove the oil filler cap and add

1.8 Liter (2 US qt) of the specified outboard motor oil.

7. Allow a few minutes for the oil to drain into the sump and insert the oil

dipstick.

8. Remove the dipstick and inspect if the oil level is within the safe operating

range.

9. Install the dipstick and oil filler cap hand‑tight.
10. Close the service access door and lock into place by pushing on the port

side of the door.

65510

FUEL AND OIL

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 37 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: