Mercury 300R HD CMS Mechanical Скачать руководство пользователя страница 33

Страница: 33 / 99

WARNING

Fuel leakage is a fire or explosion hazard, which can cause serious injury or

death. Periodically inspect all fuel system components for leaks, softening,

hardening, swelling, or corrosion, particularly after storage. Any sign of

leakage or deterioration requires replacement before further engine

operation.

IMPORTANT: If you use gasoline that contains or might contain methanol or

ethanol, you must increase the frequency of inspection for leaks and

abnormalities.
IMPORTANT: When operating a Mercury Marine engine on gasoline containing

methanol or ethanol, do not store the gasoline in the fuel tank for long periods.

Cars normally consume these blended fuels before they can absorb enough

moisture to cause trouble; boats often sit idle long enough for phase separation

to take place. Internal corrosion may occur during storage if alcohol has

washed protective oil films from internal components.

Fuel Additives

To minimize carbon deposit buildup in the engine, it is recommended to add

Mercury or Quicksilver Quickstor fuel stabilizer additive to the engine's fuel at

each tank fill throughout the boating season. Use additive as directed on

container.

Low Permeation Fuel Hose Requirement

Required for outboards manufactured for sale, sold, or offered for sale in the

United States.

•

The Environmental Protection Agency (EPA) requires that any outboard

manufactured after January 1, 2009, must use low permeation fuel hose

for the primary fuel hose connecting the fuel tank to the outboard.

•

Low permeation hose is USCG Type B1‑15 or Type A1‑15, defined as not

exceeding 15 g/m²/24 h with CE 10 fuel at 23 °C as specified in SAE J

1527 ‑ marine fuel hose.

Fuel Demand Valve (FDV) Requirement

Whenever a pressurized fuel tank is used, a fuel demand valve is required to

be installed in the fuel hose between the fuel tank and the engine. The fuel

demand valve prevents pressurized fuel from entering the engine and causing

a fuel system overflow or possible fuel spillage.

FUEL AND OIL

eng

Содержание 300R HD CMS Mechanical




































































































Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы:

Mercury 300R HD CMS Mechanical, Руководство по эксплуатации и обслуживанию, Страница: 33 / 99

Результаты поиска

Содержание 300R HD CMS Mechanical

Отзывы: