MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 98

Страница: 98 / 148

Section 5 - Maintenance

Page 90

90-899883154 JANUARY 2008

Engine Coupler

1. Lubricate engine coupler splines through grease fittings on coupler by applying

approximately 8‑10 pumps of grease from a typical hand‑operated grease gun.

NOTE: If the boat is operated at idle for prolonged periods of time, coupler should be

lubricated

Bravo Models

‑ every 50 hours;

Alpha Models

‑ every 150 hours.

6212

Bravo drive coupler

a -

Grease fitting

Tube Ref No.

Description

Where Used

Part No.

Engine Coupler Spline Grease

Coupler

92-802869A 1

NOTE:

Bravo Models

‑ The coupler and shaft splines can be lubricated without removing

the sterndrive unit. Apply lubricant from a typical hand‑operated grease gun until a small

amount of grease begins to push out.

Propellers

Propeller Repair

Some damaged propellers can be repaired. Contact your authorized Mercury MerCruiser

dealer.

Bravo Three Propeller Removal

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the

water with a propeller installed. Before installing or removing a propeller, place the drive

unit in neutral and engage the lanyard stop switch to prevent the engine from starting.

Place a block of wood between the propeller blade and the anti‑ventilation plate.

1. Place wood block between propeller blades and anti‑ventilation plate to prevent

rotation.

2. Remove the bolt and washers securing the propeller shaft anode.

Содержание Axius 496 MAG H.O.





















































































































































Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды

MerCruiser Axius 496 MAG H.O., Руководство пользователя

Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды