MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 123

Страница: 123 / 148

Section 5 - Maintenance

90-899883154 JANUARY 2008

Page 115

15.

If the boat is out of the water:

Install the water inlet hose to the aft side of the seawater

pump. Tighten the hose clamp securely.

16.

If the boat is in the water:

Tag the ignition switch with an appropriate tag requiring

the seawater inlet hose to be reconnected prior to operating engine.

SeaCore Power Package Flushing Procedure

NOTE: Flushing is needed only for salt, brackish, mineral laden or polluted water

applications. Flushing is recommended after each outing for best results.

IMPORTANT: Flushing the SeaCore power package with the boat and sterndrive in the

water is less effective. Flushing the SeaCore power package is most effective when

performed with the boat and sterndrive out of the water, such as on a boat lift or trailer.

MODELS USING THE STERNDRIVE WATER PICKUP

IMPORTANT: The system is designed to flush the Bravo sterndrive and the engine with

one water source. Do not block or remove the inlet water hose from the sterndrive to the

engine.

NOTE: Engines with the sterndrive water inlet blocked off at the gimbal housing: Refer to

Alternative Water Pickups.

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the

water with a propeller installed. Before installing or removing a propeller, place the drive

unit in neutral and engage the lanyard stop switch to prevent the engine from starting.

Place a block of wood between the propeller blade and the anti‑ventilation plate.

IMPORTANT: Do not allow the engine to pull air or seawater from alternative water pickup

sources during the flushing procedure. If equipped, ensure that all alternative water inlet

hoses are plugged at both ends.
1. Remove the boat from the water.
2. Close the seacock, if equipped.

18510

For visual clarity, the secock shown is not installed

a -

Hose fitting to engine

b -

Seacock

c -

Handle (closed position)

d -

To water source pickup attachment

3. If equipped with an alternative water pickup and not equipped with a seacock,

disconnect the water hose from the alternative water pickup and plug both ends,

excluding the Bravo sterndrive.

4. Ensure that the inlet water hose from the sterndrive to the engine is connected.
5. Remove the quick‑connect fitting from the parts bag supplied with the engine.

Содержание Axius 496 MAG H.O.





















































































































































Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды

MerCruiser Axius 496 MAG H.O., Руководство пользователя

Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды