MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 148

background image

Section 3 - On The Water

90-899883154 JANUARY 2008

Page 53

THROTTLE ONLY

31465

"THROTTLE ONLY" button

To engage Throttle Only mode:
1. Place both ERC levers in neutral.
2. Press the "THROTTLE ONLY" button, located on the DTS trackpad.
3. The "THROTTLE ONLY" button light illuminates and the neutral lights blink.
4. Place either ERC lever into gear.
5. The RPM of the engines can be increased, while the transmissions remains in Neutral.

NOTE: Pressing the "THROTTLE ONLY" button while the ERC levers are in gear, turns

off the button light, but the boat remains in throttle only mode until you place the levers in

neutral.

To disengage throttle only mode:
1. Bring both ERC levers to neutral. Throttle only will not disengage unless the ERC levers

are in neutral.

2. Press the "THROTTLE ONLY" button. The "THROTTLE ONLY" button light turns off.
3. The neutral lights remains on.

«
...
59
60
61
62
63
...
»

Содержание Axius 496 MAG H.O.





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 496 MAG H.O.

Бренд: GRITAL Страницы: 4

Jeep Six-Cylinder

Бренд: Golen Страницы: 11

Бренд: AL-KO Страницы: 144

Smart Motor SM23166MT

Бренд: MOOG ANIMATICS Страницы: 32

Бренд: DELTA DORE Страницы: 16

Бренд: Kohler Страницы: 85

Бренд: O.S. engine Страницы: 29

Бренд: Volkswagen Страницы: 64

Throttling Governor Kerosene Stationary Engines

Бренд: Worthington Страницы: 33

Бренд: Leadshine Technology Страницы: 55

Бренд: Clarke Страницы: 49

Бренд: Lycomin Страницы: 171

Бренд: RIB Страницы: 44

Бренд: Quectel Страницы: 39

Бренд: Detroit Diesel Страницы: 40

Бренд: O.S. engine Страницы: 38

Бренд: LONCIN Страницы: 22

ZAtop SM250.100C

Бренд: ZIEHL-ABEGG Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды