manualshive.com logo in svg

MerCruiser Axius 496 MAG H.O., Руководство пользователя, Страница: 84 / 148

Поделиться
Скачать
MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 84

Section 5 - Maintenance 

Page  76

90-899883154   JANUARY  2008

4. Place the oil drain hose in a suitable container.
5. Remove the drain plug from the oil drain hose.
6. After oil has drained completely, install the drain plug in the oil drain hose.
7. Push the hose through bilge drain and install the plug.

ENGINE OIL DRAIN PUMP

1. Loosen the oil filter to vent the system.
2. Remove the dipstick.
3. Install the oil pump onto the dipstick tube.

mc70571-1

a

c

b

a -

Typical oil pump

b -

Dipstick tube

c -

Oil drain hose

4. Insert the hose end of the crankcase oil pump onto an appropriate container and, using

the handle, pump until the crankcase is empty.

5. Remove the pump.
6. Install the dipstick.

CHANGING FILTER

1. Remove and discard oil filter.

8483

a

a -

Oil filter

Содержание Axius 496 MAG H.O.





















































































































































Отзывы:

Нет отзывов