MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 88

Страница: 88 / 148

Section 5 - Maintenance

Page 80

90-899883154 JANUARY 2008

3. Install the fill cap onto the coolant recovery bottle.

Changing

Contact your authorized Mercury MerCruiser dealer.

Gear Lube Oil

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by

law. Use caution not to spill oil, coolant, or other fluids into the environment when using

or servicing your boat. Be aware of the local restrictions governing the disposal or

recycling of waste, and contain and dispose of fluids as required.

Checking

NOTE: The level of gear lube oil will fluctuate during operation. Check the oil level with the

engine cold, before starting.

1. Check the gear lube oil level. Keep the oil level within the recommended operating

range. If any water is visible at the bottom of the monitor or appears at the oil fill/drain

plug or if oil appears discolored, contact your authorized Mercury MerCruiser dealer

immediately. Both conditions may indicate a water leak somewhere in the sterndrive

unit.

8530

a -

Gear lube monitor

Filling

IMPORTANT: A leaking seal may cause a lack of sufficient lubrication, which can cause

damage to the sterndrive unit. Using more than 59 ml (2 fl. oz.) of High Performance Gear

Lubricant to fill the monitor may indicate a leaking seal. Contact your authorized Mercury

MerCruiser dealer.
1. Remove the gear lube monitor cap.
2. Fill the monitor with the specified fluid so that the oil level is in the operating range. Do

not overfill.

Содержание Axius 496 MAG H.O.





















































































































































Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

MerCruiser Axius 496 MAG H.O., Руководство пользователя, Страница: 88 / 148

Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы: