MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 34

Страница: 34 / 148

Section 2 - Getting to Know Your Power Package

Page 26

90-899883154 JANUARY 2008

NOTE: When using the joystick, the computer moves the sterndrive in and out of gear

even though the ERC handles remain in neutral.

28086

Typical ERC handles

a -

Neutral

b -

Forward

c -

Reverse

d -

Bow of boat

ADJUSTMENT

The amount of force needed to move the ERC handles and to move the ERC handles

through the detentes is adjustable to help prevent unwanted motion of the handle in rough

water.
To adjust ERC handle tension:
1. Remove the port side cover for port lever adjustment, and starboard side cover for

starboard lever adjustment.

2. Turn the screw clockwise to increase tension on the control handle and

counter‑clockwise to decrease tension.

3. Adjust to tension desired.
To adjust ERC handle detent tension:
1. Remove the port side cover for port lever adjustment, and starboard side cover for

starboard lever adjustment.

2. Turn the screw clockwise to increase tension on the control handle and

counter‑clockwise to decrease tension.

Содержание Axius 496 MAG H.O.





















































































































































Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды

MerCruiser Axius 496 MAG H.O., Руководство пользователя

Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды