MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 83

Страница: 83 / 148

Section 5 - Maintenance

90-899883154 JANUARY 2008

Page 75

1. Remove oil fill cap.

5581

a -

Oil fill cap

IMPORTANT: Add the specified engine oil to bring the level up to, but not over, the full or

OK range mark on the dipstick.
2. Add the specified engine oil to bring the level up to, but not over, the full or OK range

mark on the dipstick. Recheck oil level.

3. Replace the fill cap.

All Models

Capacity

Fluid Type

Engine Oil (With Filter)

8.5 liters

(9 U.S. Quart)

Mercury/Quicksilver Synthetic Blend MerCruiser Engine Oil

25W‑40

Changing Oil and Filter

Refer to the Maintenance schedule for the change interval. Engine oil should be changed

before placing the boat in storage.
IMPORTANT: Change engine oil when the engine is warm from operation. Warm oil flows

more freely, carrying away more impurities. Use only recommended engine oil (refer to

Specifications).

EASY ENGINE OIL DRAIN SYSTEM

NOTE: Boat must be out of water to perform this procedure.

1. Loosen the oil filter to vent the system.
2. Remove the bilge drain plug.
3. Pull tether through the bilge drain.

7284

a -

Bilge drain plug

b -

Tether

c -

Clip

d -

Oil drain hose plug

e -

Oil drain hose

f -

Bilge drain flange

Содержание Axius 496 MAG H.O.





















































































































































Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды

MerCruiser Axius 496 MAG H.O., Руководство пользователя

Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды