MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 104

Страница: 104 / 148

Section 5 - Maintenance

Page 96

90-899883154 JANUARY 2008

3. Use a breaker bar and appropriate socket to position the tensioner back to the engine

running location and slide the belt over the tensioner pulley. Slowly relieve the tensioner

to the belt.

8115

Breaker bar with arrow in direction of movement to install belt

a -

Breaker bar

Corrosion Protection

Corrosion Information

Whenever two or more dissimilar metals are submerged in a conductive solution, such as

saltwater, polluted water or water with a high mineral content, a chemical reaction takes

place causing electrical current to flow between metals. The electrical current flow causes

the metal that is most chemically active, or anodic, to erode. This is known as galvanic

corrosion. For more information contact your authorized Mercury MerCruiser dealer and

refer to the

Mercury Precision Parts / Marine Corrosion Protection Guide

(90‑881813003).

Maintaining Ground Circuit Continuity

The transom assembly and sterndrive are equipped with a ground wire circuit to ensure

good electrical continuity between the engine, transom assembly, and sterndrive

components. Good continuity is essential for the MerCathode System to function

effectively.

Anodes and MerCathode System Locations

IMPORTANT: Replace sacrificial anodes if eroded 50 percent or more.
The anodes protect the metal components on the power package from galvanic corrosion,

and erode slowly over time. The following sacrificial anodes are installed at different

locations on your power package.

Содержание Axius 496 MAG H.O.





















































































































































Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды

MerCruiser Axius 496 MAG H.O., Руководство пользователя

Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды