MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 64

Страница: 64 / 148

Section 3 - On The Water

Page 56

90-899883154 JANUARY 2008

STANDBY AND ACTIVE LIGHTS

Axius Plus CAN Control Pad is disengaged (off) when the "STANDBY" light is illuminated.

You must press a button to engage a mode.
When the "ACTIVE" light is illuminated one mode of Axius is engaged (on).

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

32506

a -

"STANDBY" light

b -

"ACTIVE" light

POWER ICON

The power icon

indicates a button that engages or disengages an Axius Plus CAN

Control Pad function indicated on the button.

If you press a button that has the power icon

when that button light is on, the light turns

off for that button and the "STANDBY" light illuminates.

If you press a button with the power icon

when that button light is off, the light turns on

for that button, a single beep sounds, and the "ACTIVE" light illuminates.

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

32507

Button with power icon

a -

"AUTO HEADING" button

b -

Power icon

AUTO HEADING

1. At least one engine must be running for auto heading to function.

Содержание Axius 496 MAG H.O.





















































































































































Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды

MerCruiser Axius 496 MAG H.O., Руководство пользователя

Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды