MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 105

Страница: 105 / 148

Section 5 - Maintenance

90-899883154 JANUARY 2008

Page 97

MerCathode System—

The electrode assembly replaces the anode block. The system

should be tested to ensure adequate output. The test should be performed where boat is

moored, using Quicksilver Reference Electrode and Test Meter.

Description

Location

Figure

Gearcase anode plate

Underside of the lower gearcase

20336

Ventilation plate anode

Front of the gearcase

20338

MerCathode System

The MerCathode electrode is mounted

to the underside of the gimbal housing.

The MerCathode controler is mounted

on the engine or on the boat transom.

The controler harness connects to the

electrode harness.

20340

Anode kit (if equipped)

The boat transom

20341

Trim cylinder anodes

Mounted on each of the trim cylinders

20342

Propshaft anode (Bravo Three)

Bbehind the aft propeller

20344

Checking the Quicksilver MerCathode System

The MerCathode system should be tested to ensure adequate output. Perform the test

where boat is moored, using the reference electrode and test meter. Contact your

authorized Mercury MerCruiser dealer for service and information .

Reference Electrode

91‑76675T 1

9188

Senses and electrical current in the water when testing the

MerCathode system. Use to check hull potential.

Содержание Axius 496 MAG H.O.





















































































































































Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

MerCruiser Axius 496 MAG H.O., Руководство пользователя, Страница: 105 / 148

Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы: