MerCruiser Axius 496 MAG H.O. Скачать руководство пользователя страница 74

Страница: 74 / 148

Section 4 - Specifications

Page 66

90-899883154 JANUARY 2008

Models

Axius SeaCore 496 MAG and Axius 496 MAG

Axius SeaCore 496 MAG

H.O. and Axius 496 MAG

H.O.

Power

280 kW (375 hp)

317 kW (425 hp)

Number of cylinders

Displacement

8.1L (496 cid)

Bore and stroke

108 × 111 mm (4.25 × 4.38 in.)

Compression ratio

9.1:1

Idle RPM in neutral

650

Specified WOT RPM range

4400–4800

4600–5000

Minimum oil pressure at idle

103 kPa (15 psi)

Thermostat

71° C (160° F)

Timing at idle

Not adjustable

Firing order

1‑8‑7‑2‑6‑5‑4‑3

Electrical system

12 V negative (–) ground

Alternator rating

65 A

Recommended minimum

battery rating (Non‑DTS

models)

750 CCA, 950 MCA, or 180 Ah

Recommended minimum

battery rating (DTS models)

800 CCA, 1000 MCA, or 190 Ah

Spark plug type

AC Platinum (AC 41‑983)

Spark plug gap

1.5 mm (0.060 in.)

Fluid Specifications

IMPORTANT: All capacities are approximate fluid measures.

Engine

IMPORTANT: It may be necessary to adjust oil levels depending on installation angle and

cooling systems (heat exchanger and fluid lines).
Always use the dipstick to determine the exact quantity of oil or fluid required.

All Models

Capacity

Fluid Type

Engine oil (with filter)

8.5 liters (9 U.S. qt.) Mercury/Quicksilver Synthetic Blend

MerCruiser Engine Oil 25W‑40

Seawater cooling system (winterization use

only)

20 liters (21 U.S. qt.) Propylene Glycol and Purified Water

Closed cooling system

18 liters (19 U.S. qt.)

Mercury Extended Life Coolant/

Antifreeze or Extended Life Ethylene

Glycol 5/100 Coolant/Antifreeze mixed

50/50 with Purified Water

Sterndrive—Bravo

NOTE: Oil capacity includes gear lube monitor.

Model

Capacity

Fluid Type

Bravo Three with dual water pickups

2736 mL (92‑1/2 oz)

High Performance Gear Lubricant

Bravo Three with side water pickups only

2972 mL (100‑1/2 oz)

Содержание Axius 496 MAG H.O.





















































































































































Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды

MerCruiser Axius 496 MAG H.O., Руководство пользователя

Результаты поиска

Содержание Axius 496 MAG H.O.

Отзывы:

Похожие инструкции для Axius 496 MAG H.O.

Бренды по названию

Популярные бренды