Mercedes-Benz Freightliner Sprinter 2022, Руководство по эксплуатации

Страница: 105 / 334

Ho Hot-w t-wat ater auxiliar er auxiliary heat y heater er
FFunction of t unction of the ho he hot-w t-wat ater auxiliar er auxiliary heat y heater er
The hot-water auxiliary heater complements your
vehicle's climate control system, and has a heater
booster, auxiliary heating and auxiliary ventilation
function. In addition, the auxiliary heating system
heats the engine coolant to protect the engine and
save fuel during the warming-up phase. The auxili-
ary heating heats the air inside the vehicle to the
set temperature. It is not dependent on the heat
output of the running engine. The auxiliary heating
is operated directly using the vehicle's fuel. For
this reason, the fuel tank must have been lled
above the reserve fuel level so that the auxiliary
heating can work. The auxiliary heating automati-
cally adapts its operating mode to the outside tem-
perature and weather. It is therefore possible that
the auxiliary heating may switch from ventilation to
heating mode or from heating to ventilation mode.
When the engine is running, auxiliary ventilation is
not active. Auxiliary heating automatically switches
itself o a er a maximum of 50 minutes. You can-
not use the "auxiliary ventilation" operating mode
to cool the air inside the vehicle to below the out-
side temperature. Auxiliary heating helps to heat
up the vehicle while the engine is running and at
low outside temperatures.
Operating the hot-water auxiliary heater draws
power from the vehicle battery. Therefore, drive a
reasonably long distance a er heating or ventilat-
ing the vehicle twice in succession at most.
Auxiliary heating can be activated only at tempera-
tures below 40 °F (4.5 °C).
Switc
Switching t hing the ho he hot-w t-wat ater auxiliar er auxiliary heat y heater er on/o on/o
wit with t h the butt he button on
RReq equir uirements: ements:
R
The fuel tank is lled above the reserve level.
#
TTo switc o switch t h the auxiliar he auxiliary heating on and y heating on and o : o :
press the & button.
#
TTo activ o activat ate t e the he speci ed speci ed ttem emper peratur ature: e: switch
on the ignition and press the & button.
#
TTo deactiv o deactivat ate t e the he speci ed speci ed ttem emper peratur ature: e: press
the & button.
#
Set the temperature using the w button
and press the & button.
Colors of the indicator lamp:
R
Blue: Blue: stationary ventilation has been switched
on.
R
RRed: ed: the stationary heater has been switched
on.
R
YYellow: ellow: a departure time has been preselected.
The stationary heater or ventilation switches o
a er a maximum of 50 minutes.
#
TTo activ o activat ate heat e heater boost er booster mode: er mode: switch on the
ignition and press the & button.
#
TTo switc o switchh oo heat heater boost er booster mode: er mode: press
the & button.
Heater booster mode will be switched on as
necessary when the outside temperature is
lower than 32°F (0°C).
Se Setting t tting the ho he hot-w t-wat ater auxiliar er auxiliary heat y heater using t er using the on- he on-
boar board com d comput puter er
RReq equir uirements: ements:
R
The fuel tank is lled above the reserve level.
R
The ignition is switched on.
On-board computer:
4
Settings
5
Heating
Se Setting t tting the switc he switch-on time h-on time
#
Select Settings .
#
Select the desired departure time.
AActiv ctivating t ating the depar he departur ture time e time
#
Activate the departure time by ticking the box.
%
Ensure that A, B and C each correspond to a
programmed departure time.
%
The programmed time remains set only until
the next time the engine is started.
Selecting a pr Selecting a progr ogrammed time ammed time
#
Set the required programmed time A, B or C.
%
The required programmed time A, B or C will
appear only if the box to activate the depar-
ture time is ticked.
#
Select the required programmed time by swip-
ing le or right, e.g. A, B or C.
Climate control 103 103