Memmert INCO 108 Скачать руководство пользователя страница 6

Страница: 6 / 64

Safety regulations

1. Safety regulations

1.1 Terms and icons used

In this manual, certain common terms and icons are used to warn you of dangers or to give

you notes that are important in avoiding injury or damage. Observe and follow these notes

and regulations to avoid accidents and damage. These terms and icons are explained below.

1.1.1 Terms used

"Warning"

is always used whenever you or somebody else could be injured if you do

not observe the accompanying safety regulation.

"Caution"

is used for information that is important for avoiding damage.

1.1.2 Icons used

Prohibited sign (forbidding an action)

Do not tilt

appliance

Do not lift appliance

Warning icons (warning of a danger)

Danger of

electrical shock

Explosive

atmosphere

Danger of frost-

bite/cold burns

Warning of gas

bottles

heat/hot surfaces

Gas

Regulation signs (stipulate an action)

Disconnect the

mains plug

Wear gloves

Wear safety

shoes

Observe

information in

separate manual

Two or more

persons required

Other icons

Information on

first aid

First Aid:

Rinse eyes out

Important or

useful addition-

al information

Содержание INCO 108

































































Результаты поиска

Содержание INCO 108

Отзывы:

Похожие инструкции для INCO 108

Бренды по названию

Популярные бренды

Memmert INCO 108, Руководство по эксплуатации

Результаты поиска

Содержание INCO 108

Отзывы:

Похожие инструкции для INCO 108

Бренды по названию

Популярные бренды