Memmert INCO 108 Скачать руководство пользователя страница 53

Страница: 53 / 64

Advanced functions

4. The reference instrument should display 90.0% rh after the calibration procedure.
With

RH 20

a further comparison can be programmed at 20 % relative humidity.

If all compensation correction values are set to

0.0

% rh, the factory calibration settings

are restored.

7.6.3 CO

calibration

Customer-side calibration of appliance on controller by means of three CO

points:

CO2 5

calibration at 5 % CO

content

CO2 10

calibration at 10 % CO

content

CO2 15

calibration at 15 % CO

content (only for models with

or premium modules)

For each selected balance point a positive or negative compensation correction value can be

set.

co2 5

-0,4

20%

10%

co2 10

+1,5

co2 15

-0,7

Default calibration

Fig. 30

calibration (example)

Settingg

5. Set the desired CO

balance point in the SETUP (see page 44 ) and set accompanying

compensation correction value to 0.0 % rh.

6. With a reference instrument, measure the deviation in the stationary state in the selected

balance point.

7. Set the compensation correction value in the SETUP. If the measured reference CO

content

is too low, the compensation correction value must be set with a negative sign.

8. Perform a control measurement with the reference instrument.
9. The procedure can be performed for the CO

balance points 5 %, 10 % and 15 %

(15 % only for models with CO

or premium modules).

Содержание INCO 108

































































Результаты поиска

Содержание INCO 108

Отзывы:

Похожие инструкции для INCO 108

Бренды по названию

Популярные бренды

Memmert INCO 108, Руководство по эксплуатации

Результаты поиска

Содержание INCO 108

Отзывы:

Похожие инструкции для INCO 108

Бренды по названию

Популярные бренды