Memmert INCO 108 Скачать руководство пользователя страница 35

Страница: 35 / 64

Operation and control

IN 1

IN 2

OUT

After the setpoint temperature has been reached,

the CO

concentration is displayed in %, depending

on the setting.

IN 1

indicates that gas bottle 1

is active.

Is displayed if the CO

concentration exceeds the

defined setpoint by at least 1 % for more than 3

minutes. If the concentration is higher, the CO

display and the icon flash.

In this case you should open the door for 30 sec.

and wait to see if the controller steadily adjusts

to the setpoint. If the error occurs again, contact

Customer Service.

This monitoring function only starts to work

once the CO

setpoint has been reached.

CO2 empt

is displayed if gas bottle 1 and/or 2 is/are

empty. In this case, you should connect new gas

bottles (see page 26 ).

The pressure in the gas bottles is a constant

approx. 57 bar at 20 °C ambient temperature. It

is not possible to determine how full the bottle

is through the pressure, since the pressure only

drops immediately before the bottle is com-

pletely empty.

The CO

supply is automatically interrupted when

the outer doors are opened.

door open

is indicated

in the text display.

off

e m p t y

supply is interrupted. In this

case, check if the N

bottle is correctly connected

and if the valve is open.
If that does not solve the problem, you should con-

nect a new gas bottle (see page 23 ).

Automatic switch-over of CO

gas bottles (only for models with comfort or premium

(

modules))

The automatic switch-over of gas bottles guarantees an uninterrupted supply with CO

gas

when two independent supply systems are connected.

Gas bottle 1 is always the main supply bottle.

Gas bottle 2 is always the reserve bottle.

Operation is only possible with one bottle. In this case it must be connected to IN1 (see also

Fig. 4 on page 13 ).

Содержание INCO 108

































































Результаты поиска

Содержание INCO 108

Отзывы:

Похожие инструкции для INCO 108

Бренды по названию

Популярные бренды

Memmert INCO 108, Руководство по эксплуатации

Результаты поиска

Содержание INCO 108

Отзывы:

Похожие инструкции для INCO 108

Бренды по названию

Популярные бренды