Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 88

background image

Mellanox Grid Director 4700 Installation Manual

65

7

Installing System Boards

7.1

Chassis Board Configuration

Boards must be installed in their designated slot to enable their full functionality. All boards
are hot swappable and therefore can be inserted and extracted without turning off electrical
power on the 4700 chassis.

The 4700 chassis is factory pre-assembled with fan units. Additional boards and modules are
shipped according to the system configuration and are added during installation. Refer to

System Configurations

(on page

for a list of the possible chassis configurations.

Every slot that is not populated with a module must be covered with a blank panel for
proper cooling.

7.1.1

4700 Chassis

The front panel of a Grid Director 4700 includes:



Nine slots for Fabric Boards (sFB)



sFU-40H horizontal fan unit



sFU-40V vertical fan unit

The rear panel of a Grid Director 4700 includes:



18 slots which can be filled with line boards (324 ports)



Two slots for management boards (sMB)



Six bays for power supply modules (the power supplies can be installed in any of the bays,
without restriction)

Mellanox Grid Director™ 4700 Overview

(on page

) for illustrations of front and rear

panels of a fully populated 4700 chassis.

7.2

Inserting/Extracting Boards

When handling electronic boards, wear grounding wrist straps to avoid ESD damage to
the card. Do not touch the Midplane with your hand or any metal tool, or you could shock
yourself.

Fabric boards, management boards, and line boards have ejectors that lock the board in place
and serve as levers for seating or extracting.



The ejectors snap inward to lock the board in place.



Two screws on each board complete the seating and lock of the board in place.

The following figures illustrate the ejectors action (the photos below are of the previous
design; the new design has

black plastic covers

).

«
...
63
64
65
66
67
...
»

Содержание Grid Director 4700

























































































Отзывы:

Нет отзывов

Похожие инструкции для Grid Director 4700

Бренд: Daxten Страницы: 2

Бренд: tbs electronics Страницы: 2

Бренд: H3C Страницы: 204

H3C S7500E Series

Бренд: H3C Страницы: 44

H3C S7500E Series

Бренд: H3C Страницы: 11

H3C S7500E Series

Бренд: H3C Страницы: 25

Бренд: H3C Страницы: 46

Бренд: StarTech.com Страницы: 24

OmniView Secure F1DN102Uea

Бренд: Belkin Страницы: 36

Elinx EIR418-2SFP-T

Бренд: B&B Electronics Страницы: 25

Бренд: CIS Страницы: 3

Бренд: NETGEAR Страницы: 2

Бренд: Lantech Страницы: 30

iBootBar iBB-DC8

Бренд: Dataprobe Страницы: 36

Бренд: Radio Shack Страницы: 8

Бренд: TP-Link Страницы: 34

Бренд: Little Giant Страницы: 8

Бренд: Veris Industries Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды