Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 8

Страница: 8 / 88

Contents

Preface

About this Manual

This manual provides installation instructions for the Mellanox Grid Director

4700 40Gb/s

InfiniBand Switch, the product specifications, unpacking and installation information, unit
power up, and initiation and troubleshooting procedures.

Refer to the official and latest product release notes for last-minute updates.

Technical support may be obtained directly from:



Your regional distributor from whom this product was ordered



Your OEM customer representative

For further information and assistance, go to

http://www.mellanox.com/content/pages.php?pg=support_index

Audience

The manual is intended primarily for system administrators who are authorized to install a
Grid Director 4700 switch.

It is assumed that the readers are familiar with the InfiniBand technology and terminology.

Related Documentation

For additional information, refer to the following documents:



Grid Director Family Getting Started Guide [LIT-00037]



Grid Director Family User Manual [DOC-00785]



Grid Director Family Release Notes [DOC-00962]



Regulatory and Compliance Reference Guide [DOC-00859]

Document Conventions

The following lists conventions used in this document.

NOTE:

Identifies important information that contains helpful suggestions.

Содержание Grid Director 4700

























































































Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды

Mellanox Technologies Grid Director 4700, Руководство по установке

Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды