Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 55

Страница: 55 / 88

Mellanox Grid Director 4700 Installation Manual

6.2.1

Rail Kit and Mounting Components

The 4700 package includes:



Rail kit



Mounting ears (or 19" brackets) that are factory installed at the front of the chassis

The supplied rail kit is adjustable to allow for mounting the chassis in racks of varying depths.
The rail bracket kit includes the following items:



Left bracket (left rail)



Right bracket (right rail)



2 inserts (with elongated holes) – same for both left and right rails



8-32 screws 5/8" (qty: 2 x 8)



8-32 screws 3/8" (qty: 2 x 3) – to be used in case of chassis transportation in a rack.



8-32 nuts (qty: 2 x 11)



M4 flat washers (qty: 2 x 11)



Spring washers (qty: 2 x 8)



Tooth washers (qty: 2 x 3)

Clip nuts are not provided.

6.2.2

Rail Kit Assembly Overview

This section shows a diagram of an assembled rail kit and provides the procedures for
assembling the rail kit.

Содержание Grid Director 4700

























































































Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды

Mellanox Technologies Grid Director 4700, Руководство по установке

Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды