Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 83

Страница: 83 / 88

Mellanox Grid Director 4700 Installation Manual

The following figure shows cabling between two 4700 installed back to back for a 648-port
configuration:

Figure 37: Cabling Dressing between Switches Installed Back-to-Back

9.3

InfiniBand Cabling Guidelines

It is recommended to dress the cables connected to the InfiniBand connectors of each sLB into
two groups, left and right, and fasten them down gently after connectivity has been verified.

The cables from the same half of the Line Boards are bundled on the corresponding hangers
and will be routed down along the Rack side wall.

Cables should be arranged so that each Line board’s cables don’t interfere with the neighbor
Line Board insertion or removal.

Содержание Grid Director 4700

























































































Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды

Mellanox Technologies Grid Director 4700, Руководство по установке

Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды