Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 88

background image

Mellanox Grid Director 4700 Installation Manual

79

9.1.2

InfiniBand Cabling on Either Side of the Chassis (for Line Cables)

It is recommended to dress the cables connected to the InfiniBand connectors of each line
board into two groups, left and right, and fasten them down gently after connectivity has been
verified.

The cables from the same half of the line boards are bundled on the corresponding hangers and
will be routed down along the rack side wall.

Cables should be arranged so that each line board’s cables do not interfere with the neighbor
line board insertion or removal.



To connect an InfiniBand cable to an sLB-4018 Line Board:

1.

Route the cable to the nearest cabling guide bracket hanger position.

2.

Position the InfiniBand cable connector with the pulling tab at top, and push the connector
in place.

3.

Verify that the cable is inserted properly into the connector by gently tugging the cable;
verify that the Link State green-colored LED lights (and does not flash) indicating a good
physical connection.

4.

Gently fasten in place with Velcro tie or tie wraps.



Avoid using tie wrap guns or similar tools; do not fasten the InfiniBand cable too tightly, as this
may cause irreversible damage to the cables. Tie wraps and zip ties can damage the cables.
Velcro tie is the recommended option.



Do not bend the InfiniBand cables too sharply. The recommended minimum bend radius is 4"
(10 cm).

«
...
77
78
79
80
81
...
»

Содержание Grid Director 4700

























































































Отзывы:

Нет отзывов

Похожие инструкции для Grid Director 4700

Switch 4500 Family

Бренд: 3Com Страницы: 16

PathBuilder S200 Series

Бренд: 3Com Страницы: 32

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Бренд: Jabra Страницы: 4

Бренд: SMSC Страницы: 458

Бренд: Eaton Страницы: 43

Бренд: Ruby Tech Страницы: 2

SecureStack C3K-2XFP IOM

Бренд: Enterasys Страницы: 72

Бренд: Key Digital Страницы: 20

Бренд: DLS Страницы: 226

Бренд: Gefen Страницы: 14

DH-PFS3206-4P-120

Бренд: Dahua Страницы: 19

Бренд: G&D Страницы: 80

Бренд: Voith Страницы: 98

Gigabit Switch 8

Бренд: 3Com Страницы: 2

Бренд: Shadow Страницы: 4

5-Port Gigabit Switch 1000 Mbps

Бренд: Hama Страницы: 2

Бренд: Elk Products Страницы: 2

Бренд: Kramer Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды