Meler Micron PUR LC Скачать руководство пользователя страница 9

Страница: 9 / 106

SAFETY GUIDELINES

1-1

MA-5184-ENG

PUR LC/MC ADHESIVE MELTER

1. SAFETY GUIDELINES

General

The information contained in this section applies not only to everyday

equipment operation, but also to any procedure carried out on it, whether for

preventive maintenance or in the case of repairs and the replacement of worn

out parts.

It is very important to observe the safety warnings in this manual at all times.

Failure to do so may result in personal injury and/or damage to the equipment

or the rest of the installation.

Before beginning work on the equipment, read this manual carefully, and in

case of any doubt, contact our Technical Service Center. We are available for

any clarification that you might need.

Keep manuals in perfect condition and within reach of personnel that use the

equipment and perform maintenance on it.

Also provide necessary safety material: appropriate clothing, footwear, gloves

and safety glasses.

In all cases, observe local regulations regarding risk prevention and safety.

Symbols

The symbols used on both the melter/applicator equipment and in this manual

always represent the type of risk we are exposed to. Failure to abide by a

warning signal may result in personal injury and/or damage to the equipment

or the rest of the installation.

Warning:

Risk of electrical shock. Carelessness may produce injury or death.

Warning:

Hot zone with high temperatures. Risk of burns. Use thermal

protective equipment.

Warning:

System under pressure. Risk of burns or particle projection. Use

thermal protective equipment and glasses.

Warning:

Important information for the correct use of the system. May include

one or several of the previous hazards, and therefore must be kept in mind to

avoid damage and injury.

Warning:

Dangerous area. Risk of entrapment. Carelessness may produce

injury or death.

Содержание Micron PUR LC











































































































Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды

Meler Micron PUR LC, Инструкция по эксплуатации

Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды