manualshive.com logo in svg

Meler Micron PUR LC, Инструкция по эксплуатации

Поделиться
Скачать
Meler Micron PUR LC Скачать руководство пользователя страница 44

MELER GLUING SOLUTIONS

4-10

MELTER OPERATION

Pumping status

083

Zone heating.

 

There is no physical connection of components in that zone.

---

Temperature sensor error in that zone.

150

Zone in Temperature OK.

120

Zone in Standby mode.

52

Zone in Inhibition mode (OFF).

165

Zone in overheating or low temperature warning.

Note: 

For a zone to be able to give a low temperature warning, it must have 

first reached its set point temperature.

170

Zone in overheating or low temperature alarm.

Note: 

For a zone to be able to give a low temperature warning, it must have 

first reached its set point temperature.

Access the SHORTCUTS menu by pressing the temperatures area.

Temperature status

Pumping not activated.

Pumping activated.

Pumping error.

Access the PUMPING menu by pressing the icon.

Содержание Micron PUR LC











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды