Meler Micron PUR LC, Инструкция по эксплуатации

Страница: 54 / 106

MELER GLUING SOLUTIONS
4-20
MELTER OPERATION
A - Heating options configuration.
B - General settings of the unit.
C - Automatic loading configuration.
D - Access to statistics.
E - Pumping options
Main Menu
ENGRANE
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
ENGRANE
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
ENGRANE
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
ENGRANE
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
ENGRANE
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
ENGRANE
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
5. Pumping
Menu
1. Heating 2. Settings
3. Charge 4. Statistics
A
C
B
D
E
Configuring speed ramp
For equipment operating in external reference, the display will show the cu-
rrent pump rotation set point (input reference conversion as per the full scale
and the conversion table).
The conversion table may be programmed with up to 5 points (input voltage
(Voltage) and output speed (RPM)).
By default the table is programmed (0 V = 0 rpm and 10 V = 100 rpm):
Notes on the editable values in the conversion table:
• The value for voltage must always be shown to one decimal place.
• Point 1 is the starting point for the speed ramp, and therefore the vol-
tage will always be 0, while the value for output RPM is editable.
• The possible values for each point must be equal to or greater than the
value corresponding to the previous point.
• Point 5 is the final point for the speed ramp, and therefore the voltage
will always be 10, while the value for output RPM is editable.
• It is not necessary to program the value for MAXIMUM RPM in this table.
• If, at any point, the maximum value for Voltage = 10 V is entered, the
corresponding values for Vin and RPM at higher points will be automa-
tically updated according to the value for this point.
• If, at any point, the maximum value is entered, that is, RPM = MAXI-
MUM RPM, the corresponding values for RPM at higher points will be
automatically updated to MAXIMUM RPM.