Meler Micron PUR LC Скачать руководство пользователя страница 48

Страница: 48 / 106

MELER GLUING SOLUTIONS

4-14

MELTER OPERATION

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

75 rpm

50 rpm

49 rpm

53 rpm

PUMP 1

Real speed:

External reference 1

External permission 1

Switch 1

Real speed:

External reference 2

External permission 2

Switch 2

PUMP 2

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

3,5 V

100

Volt

rpm

0,0

3,0

4,0

7,0

100

Pumping

Analog input

Pumping control menu

This menu allows you to configure the operating options for each of the pumps
installed.

• Start or stop pumping:

If external permission is deactivated, when you

press the ‘Pump 1/2’ key, pumping is activated or stopped manually.

When the key is green, the pump is in operation. When it is grey, the pump

is off.

• Pumping speed:

If the external speed reference is deactivated, when this

is pressed you can set the pump’s speed.

The minimum and maximum values that can be set are established in the

pump’s minimum and maximum speed alarms. See the point ‘Menu 5.

Pumping/Pumping alarms’.

At the bottom, the display shows the actual pumping speed at that

moment.

• External reference:

Activates or deactivates the external speed control of

the pump.

If it is activated, it takes you to a screen to set the pumping ramp speed.

See the point ‘Configuring ramp speed’.

• External permission:

Activates or deactivates the external pumping

permission.

When the contact is activated, the LED on the right is green. When it is

deactivated, it is red.

• Switch:

Activates or deactivates pump start-up from a switch connector

installed on the unit (optional).

When the contact is activated, the LED on the right is green. When it is
deactivated, it is red.

Содержание Micron PUR LC











































































































Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды

Meler Micron PUR LC, Инструкция по эксплуатации

Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды