Meler Micron PUR LC Скачать руководство пользователя страница 45

Страница: 45 / 106

MELTER OPERATION

4-11

MA-5184-ENG

PUR LC/MC ADHESIVE MELTER

Temperature and Heating Shortcut displays

These screens give you access to the unit’s quick settings.

A - General standby of the unit (activate/deactivate).

B - General inhibition of the unit (activate/deactivate).

C - Programming of temperatures.

D - General set point temperature (all zones).

E - Temperature variation over the set point.

F - Temperature zones (14 zones).

G - Actual temperature.

H - Set point or control temperature.

• Unit ON: Setpoint temperature.
• Unit or Component on Standby: Standby Tempera-

ture.

• Component Disabled: OFF

I - Programming of zone statuses.

J - Inhibition/activation by groups of zones.

K - Group selection.

L - Activation of Standby in each zone.

M - Activation of Inhibition in each zone.

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

Group OFF

OFF Group: 1

Temperature

State

Area

Standby

OFF

T: Tank

D: Distributor

1.1: Hose 1

1.2: Applicator 1

2.1: Hose 2

2.2: Applicator 2

General Standby

General OFF

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

150

General Variation

General Set-Point

General Standby

General OFF

Temperature

State

Area

Real

Set Point

T: Tank

152

150

D: Distributor

150

1.1: Hose 1

OFF

1.2: Applicator 1

170

155

2.1: Hose 2

130

145

2.2: Applicator 2

100

A
C

Green: activated. Grey: deactivated

Содержание Micron PUR LC











































































































Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды

Meler Micron PUR LC, Инструкция по эксплуатации

Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды