Medivance Arctic Sun Stat Скачать руководство пользователя страница 43

Страница: 43 / 67

Service Manual

8.10 Replace the USB to RS232 Converter (T.I.M.)

1. Disconnect the RS232 cable from the back of the

USB to RS232 converter (T.I.M.).

2. Detach the USB to RS232 converter (T.I.M.) from

the top of the card cage.

4. Disconnect the RS232 cable from the back of the

USB to RS232 converter (T.I.M.) and the USB cable

from connector panel bracket then remove the

connector panel bracket assembly from the device.

5. Remove the panel ESD board with blue temp

connector PCB cable from the connector panel per

step 8.8 and install on the new Connection Bracket

Assembly.

6. Reconnect and route all wiring, reference (figure

8-25) for placement of AC Breaker harness on the

back of the power switch.

Note

: Orientation of AC Breaker Harness Connections:

•

Brown wrapped with orange stays with orange

•

Brown wrapped with purple stays with purple

7. Assemble the connector panel bracket assembly to

the device and connect the blue temp connector

PCB cable to the isolation board.

Fig 8-25 Placement of AC Breaker Harness Connections

Fig 8-26 Connector Panel Bracket Assembly

3. Assemble the new USB to RS232 converter

(T.I.M.) to the top of the card cage with the USB

connection towards the connector panel (see figure

8-27).

4. Reconnect the RS232 cable to the back of the USB

to RS232 converter (T.I.M.).

Fig 8-27 Orientation of T.I.M. on top of the card cage

Fig 8-28 USB to RS232 Converter (T.I.M.)

8.11 Replace the Level Sensor

Tools and Supplies required:

• 7/16” (11mm) nut driver

• Wire cutters

1. Disconnect the gray Level Sensor harness from the

I/O Circuit Card. Remove the cable tie securing the

harness to the bracket.

2. Using a 7/16” (11mm) nut driver, remove the screw

securing the level sensor bracket.

3. Remove the level sensor along with the plastic

sheath from the tank.

4. Insert the new level sensor into the tank, ensure the

curve of the tube is facing the bottom of the tank.

5. Reinstall the bracket, reroute and connect the gray

Level Sensor harness to the I/O Circuit Card.

Содержание Arctic Sun Stat




































































Результаты поиска

Содержание Arctic Sun Stat

Отзывы:

Похожие инструкции для Arctic Sun Stat

Бренды по названию

Популярные бренды

Medivance Arctic Sun Stat, Руководство по обслуживанию

Результаты поиска

Содержание Arctic Sun Stat

Отзывы:

Похожие инструкции для Arctic Sun Stat

Бренды по названию

Популярные бренды