McIntosh MX132 Скачать руководство пользователя страница 50

Страница: 50 / 52

General Specifications

General Specifications cont

Dolby Digital Left, Center, Right Small speakers:

and DTS

80Hz-20,000Hz

Surround Small speakers:

80Hz-20,000Hz

Subwoofer:

20Hz-80Hz

Left, Center, Right Large speakers:

20Hz-20,000Hz

Surround Large speakers:

20Hz-20,000Hz

Subwoofer:

20Hz-80Hz

External Input Left, Center, Right, Left Surround,

Right Surround:

20Hz-20,000Hz

Subwoofer:

20Hz-120Hz

Rated Output

All Modes:

2.0VRMS for full bit digital input

Input Impedance

22K ohms

Output Impedance

47 ohms at all outputs

Maximum Output Voltage

9.5 VRMS

Total Harmonic Distortion

0.005% at all outputs

Sensitivity

Analog Input: 400mV for 2.0V output

Signal To Noise Ratio - All Outputs

Greater than 90dB un-weighted

Greater than 100dB A weighted

Greater than 98dB CCIR

Maximum Input Signal

Analog Input: 6Vrms

Voltage Gain

Analog Input to Output: 14dB

Frequency Response

+0, -0.5dB from 20Hz to 20,000Hz

Tone Controls

+12dB, -12dB from flat setting

Audio Specifications, cont

Power Requirements

100 Volts, 50/60Hz at 65 watts

110 Volts, 50/60Hz at 65 watts

120 Volts, 50/60Hz at 65 watts

220 Volts, 50/60Hz at 65 watts

230 Volts, 50/60Hz at 65 watts

240 Volts, 50/60Hz at 65 watts

NOTE: Refer to the rear panel of the MX132 for the correct

voltage.

Dimensions

Front Panel: 17/1/2 inches (44.5cm) wide, 7-1/16 inches

(17.9cm) high. Depth behind front mounting panel is 21

inches (53.3cm) including clearance for connectors. Panel

clearance required in front of mounting panel is 1-1/8

inches (2.9cm).

Weight

32.5 pounds (14.8Kg) net, 53.5 pounds (24.5Kg) shipping

www.eskonline.nl

Содержание MX132





















































Результаты поиска

Содержание MX132

Отзывы:

Похожие инструкции для MX132

Бренды по названию

Популярные бренды

McIntosh MX132, Руководство пользователя

Результаты поиска

Содержание MX132

Отзывы:

Похожие инструкции для MX132

Бренды по названию

Популярные бренды